CW308T-GENERIC - Revision history

Coflynn at 19:38, 29 July 2020

2020-07-29T19:38:08Z

Fheubach at 18:17, 1 May 2018

2018-05-01T18:17:04Z

Coflynn at 15:58, 2 April 2017

2017-04-02T15:58:28Z

Coflynn at 19:34, 26 March 2017

2017-03-26T19:34:41Z

Coflynn at 17:27, 25 March 2017

2017-03-25T17:27:56Z

Coflynn at 17:27, 25 March 2017

2017-03-25T17:27:23Z

Coflynn at 16:38, 25 March 2017

2017-03-25T16:38:42Z

Gdeon at 14:12, 17 January 2017

2017-01-17T14:12:26Z

Coflynn: /* Hue Bridge 2.0 */

2016-09-27T03:15:45Z

‎Hue Bridge 2.0

Coflynn: /* Usage */

2016-09-24T14:53:40Z

‎Usage

@@ Line 1: / Line 1: @@
-{{Infobox cw308target
+== Page Moved ==
-|name                   = CW308T-GENERIC / CW308T-25.4
-|image                  =
-|caption                =
-|Target Device          =
-|Target Architecture    =
-|Hardware Crypto        =
-|Purchase Hardware      =
-|Design Files           = [https://oshpark.com/shared_projects/YsDSoasu OSH Park PCBs]
-|Supported Applications =
-}}
-This is a basic prototype board which can be used for mounting other chips on the [[CW308 UFO Target]]. It can also be used to mount small boards (see the examples for photos).
+See [https://rtfm.newae.com/Targets/UFO%20Targets/CW308T-GENERIC/ NewAE RTFM Page] which is now built from the [https://github.com/newaetech/chipwhisperer-target-cw308t GIT Repo].
-== Usage ==
+The previous content on this wiki has been moved to the above link. See wiki history if you would like to view exact older versions of this page.
-−
-If using the board, you MUST wire the I/O voltage to the VREF pin (lower left, pin A20). If you fail to do this the diode clamps may stop I/O lines from being drivable.
-−
-See the example photos below where you can see the 3.3V supply being routed to the VREF pin.
-−
-== Examples ==
-−
-The following shows several examples of this board in use.
-−
-=== Hue Bridge 2.0 ===
-−
-This shows an extreme example of mounting a board onto the victim board. The actual analysis was being done on the SAMR21R on the main board, but this provided mechanical stability to allow tacking wires onto that area.
-−
-[[File:P1090113.jpg|400px]]
-−
-[[File:huebridge2.JPG|400px]]
-−
-=== Hue ATMega2564RF2R Based Bulb ===
-−
-The SPI traffic was wired out as well in this example, and a ChipWhisperer-Pro was used to trigger on SPI traffic.
-−
-[[File:P1090114.jpg|400px]]
-−
-[[File:huebulb_m2564rfr2.jpg|400px]]
-−
-=== Riscure CTF Board ===
-−
-This example allowed both power analysis and clock glitching to be performed against the board. A small shunt resistor is soldered in-line for the VCC pin.
-−
-[[File:P1090112.jpg|400px]]
-−
-[[File:riscure_ctf.jpg|400px]]
-−
-== Hardware ==
-−
-{{Template:Hardware}}
-[[Category: CW308 Targets]]

@@ Line 47: / Line 47: @@
 [[File:riscure_ctf.jpg|400px]]
 {{Template:Hardware}}
 [[Category: CW308 Targets]]

@@ Line 7: / Line 7: @@
 |Hardware Crypto        =
 |Purchase Hardware      =
-|Design Files           =
+|Design Files           = [https://oshpark.com/shared_projects/YsDSoasu OSH Park PCBs]
 |Supported Applications =
 }}

← Older revision		Revision as of 19:34, 26 March 2017
Line 49:		Line 49:

	{{Template:Hardware}}		{{Template:Hardware}}
−	~~[[Category: Hardware]]~~
−	~~[[Category: Targets]~~
	[[Category: CW308 Targets]]		[[Category: CW308 Targets]]
−	~~[[Category: Real Targets]]~~

@@ Line 1: / Line 1: @@
 {{Infobox cw308target
 |name                   = CW308T-GENERIC / CW308T-25.4
-|image                  = File:P1090088.jpg
+|image                  =
-|caption                = Image of PCB
+|caption                =
 |Target Device          =
 |Target Architecture    =
@@ Line 8: / Line 8: @@
 |Purchase Hardware      =
 |Design Files           =
-|Supported Applications = N/A
+|Supported Applications =
 }}

← Older revision		Revision as of 17:27, 25 March 2017
Line 1:		Line 1:
		+	{{Infobox cw308target
		+	\|name = CW308T-GENERIC / CW308T-25.4
		+	\|image = File:P1090088.jpg
		+	\|caption = Image of PCB
		+	\|Target Device =
		+	\|Target Architecture =
		+	\|Hardware Crypto =
		+	\|Purchase Hardware =
		+	\|Design Files =
		+	\|Supported Applications = N/A
		+	}}

	This is a basic prototype board which can be used for mounting other chips on the [[CW308 UFO Target]]. It can also be used to mount small boards (see the examples for photos).		This is a basic prototype board which can be used for mounting other chips on the [[CW308 UFO Target]]. It can also be used to mount small boards (see the examples for photos).