CW308 UFO Target - Revision history

Coflynn: Replaced content with "== Page Moved == See [https://rtfm.newae.com/Targets/CW308%20UFO/ NewAE RTFM Page]. The previous content on this wiki has been moved to the above link. See wiki history i..."

2020-07-29T19:44:38Z

Replaced content with "== Page Moved == See [https://rtfm.newae.com/Targets/CW308%20UFO/ NewAE RTFM Page]. The previous content on this wiki has been moved to the above link. See wiki history i..."

Show changes

Fheubach at 18:16, 1 May 2018

2018-05-01T18:16:44Z

LCraig at 18:03, 4 October 2017

2017-10-04T18:03:58Z

LCraig at 18:02, 4 October 2017

2017-10-04T18:02:56Z

LCraig at 18:02, 4 October 2017

2017-10-04T18:02:25Z

Coflynn at 20:17, 26 March 2017

2017-03-26T20:17:02Z

Coflynn at 19:34, 26 March 2017

2017-03-26T19:34:33Z

Coflynn at 16:46, 25 March 2017

2017-03-25T16:46:07Z

Coflynn at 16:27, 25 March 2017

2017-03-25T16:27:31Z

Gdeon: /* Usage Example: Stand-Alone */

2017-01-17T15:48:52Z

‎Usage Example: Stand-Alone

@@ Line 796: / Line 796: @@
 [[File:NAE-CW308-03_Schematic_Page_5.png|1200px]]
 {{Template:Hardware}}
 [[Category:Targets]]

@@ Line 6: / Line 6: @@
 |Status                 = Released
 }}
-The CW308 UFO Board is a handy main-board for attacking all sorts of embedded targets. Released in 2016, it forms the basis for most of our upcoming target boards. It can be used stand-alone (with an oscilloscope) or with the ChipWhisperer-Capture hardware.
+The CW308 UFO Board is a convenient main-board for attacking all sorts of embedded targets. Released in 2016, it forms the basis for most of our upcoming target boards. It can be used stand-alone (with an oscilloscope) or with ChipWhisperer-Capture hardware.
-[[File:cw308_top.png|700px]]
 == Supported Targets ==

@@ Line 1: / Line 1: @@
-{{Infobox cw308
+{{Infobox cw308target
 |name                   = CW308
 |image                  = File:CW308T_Wiki.jpg

← Older revision		Revision as of 18:02, 4 October 2017
Line 1:		Line 1:
		+	{{Infobox cw308
		+	\|name = CW308
		+	\|image = File:CW308T_Wiki.jpg
		+	\|caption =
		+	\|Purchase Hardware =
		+	\|Status = Released
		+	}}
	The CW308 UFO Board is a handy main-board for attacking all sorts of embedded targets. Released in 2016, it forms the basis for most of our upcoming target boards. It can be used stand-alone (with an oscilloscope) or with the ChipWhisperer-Capture hardware.		The CW308 UFO Board is a handy main-board for attacking all sorts of embedded targets. Released in 2016, it forms the basis for most of our upcoming target boards. It can be used stand-alone (with an oscilloscope) or with the ChipWhisperer-Capture hardware.
−
−	~~== Overview ==~~
−
−	~~[[File:cw308_fpga.png]]~~
	[[File:cw308_top.png\|700px]]		[[File:cw308_top.png\|700px]]

← Older revision		Revision as of 20:17, 26 March 2017
Line 797:		Line 797:
	{{Template:Hardware}}		{{Template:Hardware}}

−	[[Category:~~CW308~~ Targets]]	+	[[Category:Targets]]

← Older revision		Revision as of 19:34, 26 March 2017
Line 797:		Line 797:
	{{Template:Hardware}}		{{Template:Hardware}}

−
−	~~[[Category:Hardware]]~~
−	~~[[Category:Targets]]~~
	[[Category:CW308 Targets]]		[[Category:CW308 Targets]]

@@ Line 386: / Line 386: @@
 The I/O pins connected to the 20-pin header have diode clamping, with the maximum level set by the VREF network. You must ensure jumper J4 sets a correct reference level. If using any of the official victim boards this is done by setting J4 to receive it's reference level from "J5-VREF" pin.
-{{Infobox|If you do NOT set a correct VREF level, the diode clamps will pull I/O pins down to invalid levels. If you are using the prototyping board be sure to connect pin A20 (the 'VREF' pin) on the victim connector strip to the desired I/O level!}}
+{{Warningbox|If you do NOT set a correct VREF level, the diode clamps will pull I/O pins down to invalid levels. If you are using the prototyping board be sure to connect pin A20 (the 'VREF' pin) on the victim connector strip to the desired I/O level!}}
 === 20-Pin Pinout ===

← Older revision		Revision as of 16:27, 25 March 2017
Line 796:		Line 796:

	{{Template:Hardware}}		{{Template:Hardware}}
		+
		+
		+	[[Category:Hardware]]
		+	[[Category:Targets]]
		+	[[Category:CW308 Targets]]

@@ Line 763: / Line 763: @@
 == Usage Example: Stand-Alone ==
-The CW308 can be used stand-alone. This is accomplished by providing an external DC power supply, and using a SMA-BNC to connect the voltage measurement to an oscilloscope.
+The CW308 can be used stand-alone. This is accomplished by providing an external DC power supply, and using a SMA-BNC to connect the voltage measurement to an oscilloscope. For more details, see [[CW308T: Stand-Alone Simple Serial Example (AVR or XMEGA)]].
 If using a simple-serial target (such as the XMEGA or AVR), you can connect a USB-Serial device to provide communication.