Fheubach at 18:25, 1 May 2018

2018-05-01T18:25:09Z

Fheubach at 13:39, 1 May 2018

2018-05-01T13:39:10Z

Gdeon at 14:14, 17 January 2017

2017-01-17T14:14:04Z

Coflynn: Created page with "= SAKURA-G Target = == Preparing the SAKURA-G Hardware == The SAKURA-G must be prepared for use with the ChipWhisperer system. This requires the OpenADC device mounted using..."

2016-03-29T16:35:03Z

Created page with "= SAKURA-G Target = == Preparing the SAKURA-G Hardware == The SAKURA-G must be prepared for use with the ChipWhisperer system. This requires the OpenADC device mounted using..."

New page

= SAKURA-G Target =

== Preparing the SAKURA-G Hardware ==

The SAKURA-G must be prepared for use with the ChipWhisperer system. This requires the OpenADC device mounted using an interposer PCB. In addition the SMA connector must route the power measurement, and the trigger signal must be connected. This assumes the <code>FPGA #1</code> on the SAKURA-G has been programmed with the AES example.

A Xilinx Platform USB Cable or similar is used for programming. The complete setup looks as follows:

[[File:sakurag_hardware.jpg|image]]

You must then run Xilinx Impact program, and have it detect the Spartan 6 LX9 device. You can then add a SPI Flash:

[[File:addspiflash.png|image]]

This will prompt you to specify the PROM file. This file is located in <code>chipwhisperer\hardware\capture\sakura-g\sakurag_ise_project\sakurag-chipwhisperer.mcs</code>.

[[File:addpromfile.png|image]]

Finally select the SPI Flash Type. Confirm the part number by looking at part U13 on the SAKURA-G, just to the right of the LX9 FPGA.

[[File:selectflash.png|image]]

You can now program the SPI Flash. This step will take some time to complete. Once this is done you have a working ChipWhisperer system.

[[File:rightclick-program.png|image]]

== Running SAKURA-G Example ==

The SAKURA-G has an example script shipped with the ChipWhisperer release, which can be run from the ChipWhisperer-Capture environment.

You can see a [http://www.youtube.com/watch?v=hykeV8DCf2M&hd=1 Video] of the system working on YouTube:

[[File:sakuragyoutube.png|link=http://www.youtube.com/watch?v=hykeV8DCf2M&hd=1]]

← Older revision		Revision as of 18:25, 1 May 2018
Line 31:		Line 31:
	[[File:sakuragyoutube.png\|link=http://www.youtube.com/watch?v=hykeV8DCf2M&hd=1]]		[[File:sakuragyoutube.png\|link=http://www.youtube.com/watch?v=hykeV8DCf2M&hd=1]]

		+	== Hardware ==

	{{Template:Hardware}}		{{Template:Hardware}}

← Older revision		Revision as of 13:39, 1 May 2018
Line 1:		Line 1:
−	~~= SAKURA-G Target =~~
−
	== Preparing the SAKURA-G Hardware ==		== Preparing the SAKURA-G Hardware ==

← Older revision		Revision as of 14:14, 17 January 2017
Line 32:		Line 32:

	[[File:sakuragyoutube.png\|link=http://www.youtube.com/watch?v=hykeV8DCf2M&hd=1]]		[[File:sakuragyoutube.png\|link=http://www.youtube.com/watch?v=hykeV8DCf2M&hd=1]]
		+
		+
		+	{{Template:Hardware}}

SAKURA-G Target - Revision history

Fheubach at 18:25, 1 May 2018

Fheubach at 13:39, 1 May 2018

Gdeon at 14:14, 17 January 2017

Coflynn: Created page with "= SAKURA-G Target = == Preparing the SAKURA-G Hardware == The SAKURA-G must be prepared for use with the ChipWhisperer system. This requires the OpenADC device mounted using..."