Programming Microcontroller

The target board contains an ATMega165PA/ATMega325PA (referred to as the 'AVR' hereafter), which can be used for performing program verification. It is also used to generate trigger points for attacks such as encryption table read-out & inserting glitches into the program read logic. The programming interface contains the following limitations:

• No programming is possible as there is no VPP generation.
• Address lines A0 - A13 are mapped to the AVR. The upper two lines are shared with LED1/LED2 outputs. (A14 and A15 aren't needed because the 87C51 model that's used only has 16 KB = 2^14 bytes of memory.)

Target Microcontroller

The default target device is an Intel EE87C51RB1 (16K EPROM, 512 RAM). Useful references:

• Intel 8xC51RA,RB,RC Datasheet
• NXP 8XC51RA+/RB+ Datasheet

NOTE: The Intel datasheet is fairly short (20 pages) and does not include full details of the programming. This can be found in the NXP datasheet.

There are 2 20-pin headers on the top side of the board connected to the pins of the 87C51. If you're keeping track, the remaining 4 pins are labelled NC - they aren't used internally, so all of the functional pins are broken out to these headers. These headers make it easier to connect an oscilloscope or logic analyzer to the target.

Jumpers

A number of jumpers are present on the target board. They are mostly used to select different features and options on the target board. First, there are 7 jumpers that connect to the IO lines of the two microcontrollers

• IO MODE (J1): Selects if the AVR is enabled or not. When the board is powered on, if this is set to "RUN", the AVR will enter sleep mode until the power is cut. If it is set to "PROG", the AVR will continue executing its program.
• EA/VPP (J2): Selects the 8051's EA pin connection. In "PROG" mode, the AVR has control of this pin; in "RUN" mode, it is always set to 1. This is necessary to allow the 8051 to execute code from internal EPROM memory.
• TXD (J3): Connects the Target IO2 line (Serial TXD) to one of the chips. In "PROG" mode, this is connected to AVR PE1. In "RUN" mode, it is connected to 8051 P3.1.
• RXD (J4): Connects the Target IO1 line (Serial RXD) to one of the chips. In "PROG" mode, this is connected to AVR PE0. In "RUN" mode, it is connected to 8051 P3.0.
• GPIO4 (J5): Connects the Target IO4 line to AVR PE3 ("AVR" mode) or 8051 P1.0 ("51/P1.0" mode). This line is intended to be used as a trigger, so firmware on the 8051 and AVR can cause a trigger by toggling these wires.
• GPIO3 (J6): Connects the Target IO3 line to AVR PE5 ("AVR" mode) or 8051 RESET ("51-RST" mode). In the former, the AVR has control over the 8051's reset line. In the latter, the 8051 uses an active-high reset, so the device runs when GPIO3 is set low.
• AVR MODE (J7): Connects to AVR PE4. This is normally pulled up to VCC. With a jumper connected in "OPT" mode, this is set low.

Then, there are two jumpers that control the power and clock signals:

• VCC (J11): Connects to the board's VCC rails. This can be connected to the baseboard's 5V rail or to one of the 3.3V regulator outputs. Be cautious with this - in particular, the ChipWhisperer Lite does NOT have 5V tolerant IO lines!
• J12: When J12 is not connected, the AVR runs on its own 7.37 MHz crystal. With J12 connected, the AVR's clock line is connected to CLKIN signal, which is also the 8051's clock line. Connecting the clock signals is useful for ensuring that the devices are synchronized, but it also causes any glitched clock signals to be routed to AVR.

Finally, the baseboard's "Target-Defined Programming" header (J15) is connected to some of the 8051 pins. P3.3, P3.4, and P3.5 are connected to H2, H4, and H6. Normally, these pins are all pulled down to ground (logic 0). When a jumper is mounted to H1-H2, H3-H4, or H5-H6, these pins are instead connected to VCC (logic 1).

Developing Firmware for the 87C51

There are a number of tools that can be used to develop firmware for the 87C51 processor. The best 8051-specific software can be pretty expensive, but it is possible to get by with free software:

Compiler: The SDCC (Small Device C Compiler) is a compiler that is made for devices with limited amounts of memory. It can be used to compile code specifically for a number of targets, including the 8051 line of processors. A few of the useful flags are:

• -mmcs51: Compile code specifically for an MCS51 target
• --iram-size [size]: Specify that the device has [size] bytes of internal RAM
• --xram-size [size]: Same as above, but for external RAM
• --code-size [size]: Same as above, but for code memory (EPROM)
• --out-fmt-ihx: Produce an Intel HEX file as the output of the linking stage
• --stack-auto: Put all automatic variables on the stack, rather than storing a specific location in RAM for them. This can be a huge RAM saver!

Note that SDCC has not completely implemented the ISO C99/C11 standards. One very noticeable change is that SDCC does not allow variables declarations to be intermingled with code. That is, the following will not compile:

void func()
{
	int x = 1; // OK
	x += 2;    // OK
	int y = x; // syntax error: token -> 'int'
}

Simulator: The 87C51 is one-time programmable, so it is extremely helpful to have a simulator to test firmware before burning it onto a physical processor. There are very few free simulators for the 8051 core. One free sim is EdSim51. This program can load a hex file and run the code one step at a time. There are a few big issues:

• The simulator has no way of translating your compiled binary file back into C. This means that the debugging process is a bit blind - moving through the program one line at a time isn't particularly helpful because one line of C will typically be many lines of assembly. It's still possible to debug code by printing variables, but this leaves something to be desired.
• EdSim51 is designed for an 8051 core with 128 B of RAM. This means that you cannot simulate any programs that use more than 128 B of RAM. However, this is enough space for a lot of tasks - our full piece of firmware does AES over SimpleSerial in this much space!

Programmer: To write a program into the code EPROM, an EPROM programmer is needed. We used a MiniPro TL866 programmer along with their free software. However, any programmer compatible with the 87C51 should be fine.

Default Firmware

Verification Process

Security

Gotchas