|
|
| Line 1: |
Line 1: |
| − | [[File:CW503.jpg|800px]]
| + | == Page Moved == |
| | | | |
| − | The CW503 provides a handy power supply for both the differential probe and the LNA. Multiple probes can be connected to a single power supply. The following shows the internal block diagram of the CW503 probe power supply:
| + | See [https://rtfm.newae.com/Tools/CW503%20Probe%20Power%20Supply/ NewAE RTFM Page]. The previous content on this wiki has been moved to the above link. See wiki history if you would like to view exact older versions of this page. |
| − | | + | |
| − | [[File:blockdiagram.png|image]] | + | |
| − | | + | |
| − | The use of isolated DC-DC converters allows you to use connected probes without worry about ground loops. Note the probe is ''not designed'' for use at high isolation voltages (>30V).
| + | |
| − | | + | |
| − | The power supply uses a micro-USB jack, allowing you to power the probe from front-pane USB ports on some instruments (be careful of current limits if using this method):
| + | |
| − | | + | |
| − | [[File:diffprobe-psu.jpg|400px|image]]
| + | |
| − | | + | |
| − | Alternatively the probe comes with a high-quality 5.0V wall-wart adapter, which has been selected for minimum noise input to the CW503.
| + | |
| − | | + | |
| − | == Front-Panel Connections ==
| + | |
| − | | + | |
| − | The following can be found on the front panel of the device:
| + | |
| − | | + | |
| − | <ul>
| + | |
| − | <li><p>Power Good LEDs:</p>
| + | |
| − | <blockquote><p>The probe PSU monitors the +7.8V, -7.8V, and +3.3V outputs. If these outputs fall below the required setpoints the LEDs extinguish. This is normally due to excessive current draw or a short on one of the output lines.</p></blockquote></li>
| + | |
| − | <li><p>6-Pin Probe PSU Connectors:</p>
| + | |
| − | <blockquote><p>This probe supply connectors use the same pinout as our Low Noise Amplifier (CW502) and Differential Probe (CW501). The pinout is as follows:</p>
| + | |
| − | {|
| + | |
| − | ! Pin
| + | |
| − | ! Name
| + | |
| − | |-
| + | |
| − | | 1
| + | |
| − | | +7.8V Out
| + | |
| − | |-
| + | |
| − | | 2
| + | |
| − | | GND
| + | |
| − | |-
| + | |
| − | | 3
| + | |
| − | | Aux Out
| + | |
| − | |-
| + | |
| − | | 4
| + | |
| − | | +3.3V Out
| + | |
| − | |-
| + | |
| − | | 5
| + | |
| − | | -7.8V Out
| + | |
| − | |-
| + | |
| − | | 6
| + | |
| − | | GND
| + | |
| − | |}
| + | |
| − | </blockquote></li>
| + | |
| − | <li><p>PROBE-GND Pin Header:</p>
| + | |
| − | <blockquote><p>This pin header connects to the GND pins on the 6-pin connector.</p></blockquote></li>
| + | |
| − | <li><p>AUX-IN Pin Header:</p>
| + | |
| − | <blockquote><p>This pin header connects to the "Aux Out" pin on the 6-pin connector.</p></blockquote></li>
| + | |
| − | <li><p>USB-GND Pin Header:</p>
| + | |
| − | <blockquote><p>This pin header connects to the USB negative (ground). You can connect this to the PROBE-GND to remove the isolation, or use a resistor if you want to reduce voltage differential without directly connecting them.</p></blockquote></li></ul>
| + | |
| − | | + | |
| − | == Hardware ==
| + | |
| − | | + | |
| − | {{Template:Hardware}}
| + | |
