|
|
| (18 intermediate revisions by 3 users not shown) |
| Line 1: |
Line 1: |
| − | The CW1200 (ChipWhisperer Pro) is an upgraded version of the ChipWhisperer Lite capture hardware. The Pro includes an FPGA with much more space than the Lite, allowing many new features to be added, including a larger sample buffer, streaming-mode captures, additional trigger methods, and a touchscreen interface. These features make it a high-end device suitable for laboratory use.
| + | == Page Moved == |
| | | | |
| − | Check out a [https://youtu.be/qS6JwX4SBOI sneak peek of the CW-Pro].
| + | See [https://rtfm.newae.com/Capture/ChipWhisperer-Pro/ NewAE RTFM Page]. The previous content on this wiki has been moved to the above link. See wiki history if you would like to view exact older versions of this page. |
| − | | + | |
| − | [[File:cwpro_invisible.png]]
| + | |
| − | | + | |
| − | = Power Supply =
| + | |
| − | The ChipWhisperer Pro can only be powered through its 5 V jack. It cannot be powered through the USB port - internally, there are no connections to the USB port's 5 V rail. This limitation is primarily due to the high current draw of the Pro: while powering the touchscreen running and an external target, it would be easy to exceed the USB current limit, causing all sorts of issues. | + | |
| − | | + | |
| − | To make this setup more flexible, the Pro ships with two power sources:
| + | |
| − | * A 5 V, 2.1 A power supply. This supply is suitable for a permanent bench setup.
| + | |
| − | * A USB-to-barrel jack cable. This solution is more portable: if you're travelling with a laptop, you can use a second USB port for power. A USB charger will also work here.
| + | |
| − | If you're using the USB power cable, it is recommended to use a separate power supply to power any external target boards.
| + | |
| − | | + | |
| − | = Basic Usage =
| + | |
| − | The basic features on the Pro are exactly the same as the ChipWhisperer Lite. This means that any scripts and tutorials made for the Lite will work on the Pro, too: the connectors and pinouts are exactly the same.
| + | |
| − | | + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = == AVR Programmer ==
| + | |
| − | |content= CW1173_ChipWhisperer-Lite/AVR Programmer}}
| + | |
| − | | + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = == XMEGA Programmer ==
| + | |
| − | |content= CW1173_ChipWhisperer-Lite/XMEGA Programmer}}
| + | |
| − | | + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = == Using Glitch Port ==
| + | |
| − | |content= CW1173_ChipWhisperer-Lite/Glitch Port}}
| + | |
| − | | + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = == Using Measure Port ==
| + | |
| − | |content= CW1173_ChipWhisperer-Lite/Measure Port}}
| + | |
| − | | + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = == 20-Pin Connector ==
| + | |
| − | |content= CW1173_ChipWhisperer-Lite/20-Pin Connector}}
| + | |
| − | | + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = == Upgrading SAM3U Firmware ==
| + | |
| − | |content= CW1173_ChipWhisperer-Lite/Upgrading SAM3U Firmware}}
| + | |
| − | | + | |
| − | = Advanced Features =
| + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = == Streaming Mode ==
| + | |
| − | |content= CW1200 ChipWhisperer-Pro/Streaming Mode}}
| + | |
| − | | + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = == Trigger Module ==
| + | |
| − | |content= CW1200 ChipWhisperer-Pro/Trigger Module}}
| + | |
| − | | + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = == SMA I/O ==
| + | |
| − | |content= CW1200 ChipWhisperer-Pro/SMA I/O}}
| + | |
| − | | + | |
| − | {{CollapsibleSection
| + | |
| − | |intro = = Touchscreen =
| + | |
| − | |content= CW1200 ChipWhisperer-Pro/Touchscreen}}
| + | |
| − | | + | |
| − | {{Template:Hardware}}
| + | |
| − | | + | |
| − | [[Category:Capture Hardware]]
| + | |
