|
|
| (18 intermediate revisions by 4 users not shown) |
| Line 1: |
Line 1: |
| − | {{Infobox cw308target
| + | == Page Moved == |
| − | |name = CW308T-S6LX9
| + | |
| − | |image = File:spartan6_target.jpg
| + | |
| − | |caption =
| + | |
| − | |Target Device = Spartan 6 LX9
| + | |
| − | |Target Architecture = FPGA
| + | |
| − | |Hardware Crypto = No
| + | |
| − | |Purchase Hardware = [http://store.newae.com/spartan-6-lx9-fpga-target-for-cw308/ Webstore]
| + | |
| − | |Design Files = [https://github.com/newaetech/chipwhisperer/tree/master/hardware/victims/cw308_ufo_target/spartan6lx9 GITHub link]
| + | |
| | | | |
| − | [https://oshpark.com/shared_projects/ECbBlx58 OSH Park PCBs] | + | See [https://rtfm.newae.com/Targets/UFO%20Targets/CW308T-S6LX9/ NewAE RTFM Page] which is now built from the [https://github.com/newaetech/chipwhisperer-target-cw308t GIT Repo]. |
| − | |Supported Applications = [[SimpleSerial | Simple Serial Enc]]
| + | |
| − | |Programmer = Xilinx JTAG
| + | |
| − | |Status = Released
| + | |
| − | }}
| + | |
| | | | |
| − | [[File:spartan6_target.jpg|500px]]
| + | The previous content on this wiki has been moved to the above link. See wiki history if you would like to view exact older versions of this page. |
| − | | + | |
| − | The S6LX9 target is a low-cost FPGA target. It uses the Xilinx Spartan 6 in TQFP package, and can fit an entire AES core. The example project includes the Simple-Serial interface which allows it to function like any of our other example targets. | + | |
| − | | + | |
| − | == Usage ==
| + | |
| − | | + | |
| − | The board includes a single red LED (D1) which is connected to the FPGA "DONE" pin. This pin will be HIGH (and the LED on) when the FPGA is NOT programmed. That is to say immediately on power-on, the LED will be on. Once the FPGA is successfully programmed this LED will go out.
| + | |
| − | | + | |
| − | The FPGA pins are connected to the various headers on the board. The JTAG header connects to the FPGA JTAG pins. The "Hx" pins, USART, and SPI connect to arbitrary FPGA pins.
| + | |
| − | | + | |
| − | == Example Project ==
| + | |
| − | | + | |
| − | == Known Issues ==
| + | |
| − | | + | |
| − | Note the -02 Revision of the PCB has swapped the markings of the CLKIN/CLKOUT. The correct pinout is:
| + | |
| − | | + | |
| − | * CLKIN connects to P84
| + | |
| − | * CLKOUT connects to P85
| + | |
| − | | + | |
| − | The CLKIN pin is a _N clock pin. If you need the _P clock pin, you can use a jumper on the CW308 board to route the clock input into the CLKOUT pin.
| + | |
| − | | + | |
| − | == Programming ==
| + | |
| − | | + | |
| − | The ChipWhisperer will eventually support programming this target. Until then, you will need an external programmer. This is connected via JTAG to the pin headers:
| + | |
| − | | + | |
| − | [[File:xilinx_jtag_small.jpg|400px]]
| + | |
| − | | + | |
| − | Options for programmers include:
| + | |
| − | | + | |
| − | * Xilinx Platform Cable USB or USB-II (Digikey/Mouser).
| + | |
| − | * Clone JTAG programmers off AliExpress/E-Bay for low cost (search 'Xilinx JTAG').
| + | |
| − | * Digilent Inc HS1/HS2/HS3 Cables (NB: you may need separate jumper wires).
| + | |
| − | | + | |
| − | == Schematic ==
| + | |
| − | | + | |
| − | See GIT Repo for PDF of schematic.
| + | |
| − | | + | |
| − | [[File:CW308T_S6LX9_Schematic_Page_1.png|1000px]]
| + | |
| − | | + | |
| − | [[File:CW308T_S6LX9_Schematic_Page_2.png|1000px]]
| + | |
| − | | + | |
| − | [[File:CW308T_S6LX9_Schematic_Page_3.png|1000px]]
| + | |
| − | | + | |
| − | == Board Layout ==
| + | |
| − | | + | |
| − | See GIT Repo for gerber files.
| + | |
| − | | + | |
| − | {{Template:Hardware}}
| + | |
| − | [[Category: CW308 Targets]]
| + | |
