|
|
| Line 1: |
Line 1: |
| − | {{Infobox cw308target
| + | == Page Moved == |
| − | |name = CW308T-GENERIC / CW308T-25.4
| + | |
| − | |image =
| + | |
| − | |caption =
| + | |
| − | |Target Device =
| + | |
| − | |Target Architecture =
| + | |
| − | |Hardware Crypto =
| + | |
| − | |Purchase Hardware =
| + | |
| − | |Design Files = [https://oshpark.com/shared_projects/YsDSoasu OSH Park PCBs]
| + | |
| − | |Supported Applications =
| + | |
| − | }}
| + | |
| | | | |
| − | This is a basic prototype board which can be used for mounting other chips on the [[CW308 UFO Target]]. It can also be used to mount small boards (see the examples for photos).
| + | See [https://rtfm.newae.com/Targets/UFO%20Targets/CW308T-GENERIC/ NewAE RTFM Page] which is now built from the [https://github.com/newaetech/chipwhisperer-target-cw308t GIT Repo]. |
| | | | |
| − | == Usage ==
| + | The previous content on this wiki has been moved to the above link. See wiki history if you would like to view exact older versions of this page. |
| − | | + | |
| − | If using the board, you MUST wire the I/O voltage to the VREF pin (lower left, pin A20). If you fail to do this the diode clamps may stop I/O lines from being drivable.
| + | |
| − | | + | |
| − | See the example photos below where you can see the 3.3V supply being routed to the VREF pin. | + | |
| − | | + | |
| − | == Examples ==
| + | |
| − | | + | |
| − | The following shows several examples of this board in use.
| + | |
| − | | + | |
| − | === Hue Bridge 2.0 ===
| + | |
| − | | + | |
| − | This shows an extreme example of mounting a board onto the victim board. The actual analysis was being done on the SAMR21R on the main board, but this provided mechanical stability to allow tacking wires onto that area.
| + | |
| − | | + | |
| − | [[File:P1090113.jpg|400px]]
| + | |
| − | | + | |
| − | [[File:huebridge2.JPG|400px]]
| + | |
| − | | + | |
| − | === Hue ATMega2564RF2R Based Bulb ===
| + | |
| − | | + | |
| − | The SPI traffic was wired out as well in this example, and a ChipWhisperer-Pro was used to trigger on SPI traffic.
| + | |
| − | | + | |
| − | [[File:P1090114.jpg|400px]]
| + | |
| − | | + | |
| − | [[File:huebulb_m2564rfr2.jpg|400px]]
| + | |
| − | | + | |
| − | === Riscure CTF Board ===
| + | |
| − | | + | |
| − | This example allowed both power analysis and clock glitching to be performed against the board. A small shunt resistor is soldered in-line for the VCC pin.
| + | |
| − | | + | |
| − | [[File:P1090112.jpg|400px]]
| + | |
| − | | + | |
| − | [[File:riscure_ctf.jpg|400px]]
| + | |
| − | | + | |
| − | == Hardware ==
| + | |
| − | | + | |
| − | {{Template:Hardware}}
| + | |
| − | [[Category: CW308 Targets]]
| + | |
