|
|
| (7 intermediate revisions by one other user not shown) |
| Line 1: |
Line 1: |
| − | {{Infobox cw308target
| + | == Page Moved == |
| − | |name = CW308T-AURIX
| + | |
| − | |image = [[File:CW308T_AURIX.PNG|400px]]
| + | |
| − | |caption =
| + | |
| − | |Target Device = Infineon TC233LP
| + | |
| − | |Target Architecture =
| + | |
| − | |Hardware Crypto = Yes
| + | |
| − | |Purchase Hardware =
| + | |
| − | |Design Files =
| + | |
| − | |Supported Applications =
| + | |
| − | |Status = In Developement
| + | |
| − | }}
| + | |
| | | | |
| − | This board supports the Infineon TC233LP microcontroller.
| + | See [https://rtfm.newae.com/Targets/UFO%20Targets/CW308T-AURIX/ NewAE RTFM Page] which is now built from the [https://github.com/newaetech/chipwhisperer-target-cw308t GIT Repo]. |
| | | | |
| − | == Power Supply ==
| + | The previous content on this wiki has been moved to the above link. See wiki history if you would like to view exact older versions of this page. |
| − | | + | |
| − | The core of the TC233LP chip runs from a 1.3v supply that is generated from an on-board regulator. The I/O buses are supplied with 3.3v. | + | |
| − | == Security Features ==
| + | |
| − | The TC233LP has an additional Lockstep core that runs the same instructions as the Master core (CPU0). The outputs of these cores are compared and mismatches are reported in the Safety Management Unit of the chip. This feature can only be enabled by editing the boot header of the resulting hex file.
| + | |
| − | | + | |
| − | == Programming ==
| + | |
| − | Programming of the AURIX board can currently only be done over JTAG with the Infineon DAP miniWiggler v3 using Infineon Memtool. To program the AURIX chip, begin by plugging in the miniWiggler to J6 on the CW308 board. Next, open Memtool.
| + | |
| − | | + | |
| − | Next, you'll need to add a target for the TC233LP chip. Navigate to Target > Browse and hit New. Select "Use a default target configuration" and find "Application Kit with TC234 (DAS)" under "Application Kits (DAS)", then hit "Finish". Hit "Connect". If "Ready for Memtool Command" appeared next to it, everything went smoothly.
| + | |
| − | | + | |
| − | To actually program the device, open your hex file using "Open File..." on the left hand side. Click on the address beginning with <code>0xA</code> and hit "Add Sel.>>". Finally, hit Program press the nRST button on the CW308. Current versions of the HAL will light up LED1 upon starting, so if this LED is on, your program has been successfully flashed.
| + | |
| − | | + | |
| − | == Building Projects ==
| + | |
| − | | + | |
| − | == Modifying Boot Header ==
| + | |
| − | To access some features of the TC233LP, such as the Lockstep control and disabling boot pins, the boot header at the beginning of the hex file must be modified. One way to do this is to use the "Edit" button in Memtool. After selecting the first memory range (should begin with 0xA0000000), hit "Edit". Most of the important settings are in the final 2 bytes of the second word (address 0xA0000004).
| + | |
| − | | + | |
| − | After modifying the boot header, you'll need to calculate the CRC32 of the header for addresses 0xA0000000 to 0xA0000017, as well as its compliment.
| + | |
| − | == Schematic and Layout ==
| + | |
| − | | + | |
| − | See GIT Repo for design files.
| + | |
| − | | + | |
| − | == Hardware ==
| + | |
| − | | + | |
| − | {{Template:Hardware}}
| + | |
| − | [[Category:CW308 Targets]]
| + | |
