As of August 2020 the site you are on (wiki.newae.com) is deprecated, and content is now at rtfm.newae.com.

Difference between revisions of "Manual SAM3U Firmware Update"

From ChipWhisperer Wiki
Jump to: navigation, search
(→‎Entering Bootloader Mode)
Line 22: Line 22:
  
 
If using Linux, you can use ''dmesg'' to verify the serial port was connected OK.
 
If using Linux, you can use ''dmesg'' to verify the serial port was connected OK.
 +
 +
 +
==BOSSA Command Line==
 +
 +
On certain systems it may be easier to use the command-line version of BOSSA, called bossac. You can also build just this version if required (see instructions below).
 +
 +
You can also run the BOSSA utility at the command line, with an instruction like the following:
 +
 +
bossac -e -w -v -b /path/to/SAM3U_CW1173.bin
 +
 +
If you are on Linux, you may need to either fix permissions on the serial port, or run bossac as root/sudo. See below for details.
 +
 +
=== Linux-Specific Instructions ===
 +
 +
You may need to give yourself write permission for the serial port. This can be done on some systems easily by adding yourself to the <code>dialout</code> user group. For example, assuming your username was <code>cwuser</code>:
 +
 +
# <code>$ sudo usermod -a -G dialout cwuser</code>
 +
# Log out and log back in again for changes to take effect.
 +
 +
You may also need to build bossac from sources, as the provided binary does not work with your system. Details of how to perform this are provided next:
 +
 +
To build BOSSA, it is recommended to use our simplified bossac repository, which only builds the command-line version. To build this perform these steps:
 +
 +
# Download [https://github.com/newaetech/BOSSA/archive/master.zip a copy of the GIT repo], or clone with <code>git clone git@github.com:newaetech/BOSSA.git</code> (see github.com/newaetech/bossa for the full repo).
 +
# Unzip the directory if you downloaded the zip.
 +
# Run <code>make</code>.
 +
# The binary should be in <code>bin\bossac</code>.

Revision as of 09:10, 30 June 2016

The SAM3U device has a ROM-resident bootloader. This means the bootloader is always present - unless the chip is damaged it can be run, making the device almost "unbrickable". If you have trouble running the instructions on this webpage it's most likely an issue with your host computer, and not an issue with the SAM3U being damaged.

Install BOSSA

The suggested utility to program the device is BOSSA - see [1] for details. Before proceeding, install BOSSA for your system.

Entering Bootloader Mode

The only way to enter the bootloader mode is to erase the FLASH memory. Before erasing the FLASH memory you should install the programmer tool and confirms it works (it won't connect to the device, but at least check the install works). See the next heading for details of the programming tool.

To erase the FLASH memory, simply short the jumper labeled "ERASE" on the ChipWhisperer-Lite. Do this while the device is connected via micro-USB. The blue LED should stop flashing at this point, and will stay either on or off (depending when you shorted the jumper). This can be accomplished by anything metallic - for example using a screwdriver or tweezers:

Short screwdriver.jpg

Short tweezers.jpg

Once this is accomplished, unplug and replug the micro-USB port. This will install a new driver (assuming you installed BOSSA already), and the red and blue LED should be only dimmly lit:

Lights prog.jpg

This indicates it is in bootloader mode. The device will now attach as a serial port. If you are using Windows this may take a few minutes to happen.

If using Linux, you can use dmesg to verify the serial port was connected OK.


BOSSA Command Line

On certain systems it may be easier to use the command-line version of BOSSA, called bossac. You can also build just this version if required (see instructions below).

You can also run the BOSSA utility at the command line, with an instruction like the following: 

bossac -e -w -v -b /path/to/SAM3U_CW1173.bin

If you are on Linux, you may need to either fix permissions on the serial port, or run bossac as root/sudo. See below for details.

Linux-Specific Instructions

You may need to give yourself write permission for the serial port. This can be done on some systems easily by adding yourself to the dialout user group. For example, assuming your username was cwuser:

  1. $ sudo usermod -a -G dialout cwuser
  2. Log out and log back in again for changes to take effect.

You may also need to build bossac from sources, as the provided binary does not work with your system. Details of how to perform this are provided next:

To build BOSSA, it is recommended to use our simplified bossac repository, which only builds the command-line version. To build this perform these steps:

  1. Download a copy of the GIT repo, or clone with git clone git@github.com:newaetech/BOSSA.git (see github.com/newaetech/bossa for the full repo).
  2. Unzip the directory if you downloaded the zip.
  3. Run make.
  4. The binary should be in bin\bossac.
Retrieved from "http://wiki.newae.com/index.php?title=Manual_SAM3U_Firmware_Update&oldid=941"