The CW305 target is an FPGA target board for use with the ChipWhisperer capture hardware. This board lets you test side channel analysis techniques on an Artix-7 FPGA. With this setup, a different toolchain is required: we won't be building C firmware with a makefile. This tutorial walks through the various steps required to run an AES-128 example on the CW305 target.

CW305 Hardware

If you're used to working with the ChipWhisperer Lite XMEGA or the UFO targets, the CW305 board will feel a bit different. Rather than sending data through a UART directly from the capture hardware, we'll now use two separate connections to the target board.

To get started, we need to make three connections to the CW305 target:

We'll control the Artix-7 directly from the laptop via USB. This is done through the USB-B port on the left side of the board. (On the target, the Atmel SAM3U chip converts these USB packets into signals that the FPGA can understand.)
We'll get control information for our power measurements through the 20-pin connector at the bottom of the board. This needs to be connected to your capture hardware (a ChipWhisperer Lite or Pro).
Our power measurements will be done through an SMA cable. Depending on your capture setup, there are three SMA connectors that allow access to the power line in three ways (before the shunt resistor, after the shunt, and after a low noise amplifier). For the ChipWhisperer hardware, we'll connect the third one to our capture board.

Using a ChipWhisperer Lite, the full hardware setup looks like:

Target Firmware

In the ChipWhisperer examples, the Artix-7 FPGA is programmed using Verilog. This section describes how to open and build one of these projects. It also describes the layout of the AES-128 example, which is a good starting point for making new FPGA projects.

Opening the Project

The first thing we'll need is Xilinx Vivado HLx, which is their FGPA design software. The fully featured versions of this software require a $3000+ license. However, the WEBPACK version is free, with the limitation that it can only be used with 4 families of devices (including the Artix-7). This is a huge download, so get it started while you read.

For this tutorial, a pre-existing AES-128 encryption example is waiting for us deep inside the ChipWhisperer repository. You can find this at chipwhisperer\hardware\victims\cw305_artixtarget\fpga\vivado_examples\aes128_verilog. There are a couple of files and directories here:

aes128_verilog.xpr is the project file. You can open this project using Vivado.
aes128_verilog.srcs\ contains Verilog source files for the project. Note that most of the code for this project is stored elsewhere - take a look at cw305_artixtarget\fpga\common\ and cw305_artixtarget\fpga\cryptosrc\ too.
aes128_verilog.runs\ contains the compiled output that is synthesized in Vivado. The most important part of this output is the bitstream (a .bit file), which is what we'll upload onto the target board.

When you open the project file, you should be greeted with a screen like:

This is enough for us to start poking around in the code.

FPGA Code Layout

If you're planning on making your own projects for side channel analysis, it's helpful to understand how the sample project is set up. Here's a high-level description of the different pieces:

cw305_main.xdc: The constraints file has a list of pins on the Artix-7 package. It describes how these physical pins are connected to the internal structures on the FPGA.
cw305_top.v: The top-level module defines all of the ports that are referenced in the constraints file. It connects these ports to the lower level modules. For example, the USB data and address pins are connected to a USB module here. Notably, there are two 1024 byte ports that are shared between the USB module and the register module.
usb_module.v: The USB module is used to communicate with the Atmel SAM3U microcontroller. It allows the Atmel to access the 1024 byte memory, reading from or writing to various locations in memory.
registers.v: The registers module is used to place various data into the shared memory, allowing the USB module's reads and writes to affect other modules in the code. It places this data at known, fixed offsets in the memory. For example, reading from address 0x100 allows the Atmel to recover the plaintext from an encryption.
aes_core.v: The AES core module is an implementation of AES from Google. This is taken from the ProjectVault repository.

Building the Project

This project is already fully built for us. However, if you want to make your own project, you'll need to know how to build it. There are three steps that Vivado takes to turn our Verilog into a fully functional piece of code:

Synthesis: the Verilog code is synthesized into a gate-level representation
Implementation: the synthesized logic is routed to fit onto the device
Bitstream Generation: an Artix-ready file is created, allowing us to upload our firmware onto the FPGA

This process can take a while - on an average laptop, the sample project takes around 7 minutes to build.

Gotcha: This project can be implemented to fit into an Artix-7A35T or an Artix-7A100T chip. Make sure that you have the correct one selected (right click -> "Make Active") before you build the project:

Capture Setup

With our FPGA bitstream in hand, we're now ready to capture a power trace. We can set this up using the ChipWhisperer Capture software.

To make this process simple, there is an existing sample script that connects to the CW305 using the ChipWhisperer Lite. This script is located in Project -> Example Scripts -> CW305 Artix Target w/ ChipWhisperer-Lite:

This script will connect to the CW305 and ChipWhisperer Lite, setting them up for a capture. Once the script is finished, there's one more step that we need to take - the FPGA bitstream needs to be programmed onto the Artix:

Select the bitstream file that we generated earlier (chipwhisperer/hardware/victims/cw305_artixtarget/fpga/vivado_examples/aes128_verilog/aes128_verilog.runs/impl_35t/cw305_top.bit) and program it onto the FPGA. Now, the Capture 1 button should give us a short and sweet power trace:

Success! We've built a project and recorded a power trace using the Artix target.

For further analysis using this project, check out the next tutorial: CW305: Breaking AES on FPGA.