Approved_users
510
edits
| As of August 2020 the site you are on (wiki.newae.com) is deprecated, and content is now at rtfm.newae.com. |
Changes
→Touchscreen
|content= CW1200 ChipWhisperer-Pro/SMA I/O}}
{{CollapsibleSection|intro = = Touchscreen =The touchscreen on the |content= CW1200 ChipWhisperer -Pro shows various details about its status and current settings. == Screen 1: Clock ==The clock screen shows the status of the CLKGEN and ADC clocks along with the frequency counter. '''TODO: picture'''* '''CLKGEN''': Current frequency of CLKGEN clock in kHz** '''Source''': Input to CLKGEN DCM. Could be system clock or EXTCLK** '''DCM''': Lock status of CLKGEN DCM** '''Reset DCM''': Reset the CLKGEN output. Useful if clock has locked at the wrong frequency* '''ADC Clock''': Current ADC sampling rate in kHz** '''Source''': Input to ADC DCM. Could be related to CLKGEN or EXTCLK** '''DCM''': Lock status of ADC DCM** '''Reset DCM''': Reset the ADC clock output* '''Frequency Counter''': Current frequency measured by the frequency counter** '''Source''': Input to frequency counter. Could be either EXTCLK or CLKGEN == Screen 2: Routing ==The routing screen shows the status of the various I/O pins. '''TODO: picture'''* '''Aux Output''': Status of the aux SMA connections. Could be used as trigger input/output, glitch output, and/or clock output* '''IO Pins''': Status of each of the IO pins on the 20 pin connector. Possible values depend on pin* '''Target Power State''': Status of the 3.3 V output. Can be toggled here to reset target* '''Target HS IO-Out''': Signal connected to high-speed output (HS2). Could be CLKGEN, glitch module, or disabled == Screen 3: Trigger ==The trigger screen shows the current settings for the trigger module and the ADC capture settings. '''TODO: picture'''* '''Trigger Pins''': Whether each trigger input is enabled. Active inputs are highlighted** '''Mode''': Trigger combination method. Could be AND, OR, or NAND* '''Trigger Source''': The trigger type in use. Active trigger module is highlighted** '''State''': The current output level of the trigger module* '''Trigger Mode''': The ADC trigger type. Active mode is highlighted* '''Samples''':** '''Delay''': Current ADC offset. This is the number of samples to wait after trigger before recording begins** '''Pre''': Number of pre-trigger samples to be saved** '''Time''': Delay, but converted into a time** '''Total''': Number of samples to be recorded in total* '''ADC gain''':** '''Mode''': Amplification type. Either low or high** '''Setting''': Low noise amplifier gain level == Screen 4: Glitch ==The glitch screen shows the current settings for the glitch module. '''TODO: picture'''* '''Clock Src''': Input to the glitch module's clock. Active clock is highlighted** '''DCM''': Lock status of the glitch module's DCM* '''Glitch Setup''':** '''Width''': Duty cycle of glitch pulse, as a fraction of one period** '''Fine''': Adjustment on width** '''Offset''': Distance between clock rising edge and glitch pulse rising edge, as a fraction of one period** '''Fine''': Adjustment on offset* '''View''': Schematic of glitch clock. Shows regular clock above (blue) and glitch module output below (black)* '''Trigger Src''': Input for glitch module. Active source is highlighted* '''Trigger Setup''':** '''Trigger''': Cause a manual trigger. Has no effect unless trigger source is set to Manual** '''Offset''': Number of cycles to wait before starting glitch pulses** '''Repeat''': Number of consecutive pulses to generate* '''Output Status'''** '''VCC''': Status of glitching MOSFETs. Shows warning sign if VCC glitching is enabled** '''Cnt''': Total number of glitch pulses generatedTouchscreen}}
{{Template:Hardware}}
