As of August 2020 the site you are on (wiki.newae.com) is deprecated, and content is now at rtfm.newae.com.

Changes

Jump to: navigation, search

CW308T-D2000

11,763 bytes removed, 19:32, 29 July 2020
Replaced content with "== Page Moved == See [https://rtfm.newae.com/Targets/UFO%20Targets/CW308T-D2000/ NewAE RTFM Page] which is now built from the [https://github.com/newaetech/chipwhisperer-..."
{{Infobox cw308target|name = CW308T-D2000|image = d2000_topdown.jpg|caption Page Moved = |Target Device = Intel Quark D2000|Target Architecture = x86|Hardware Crypto = No|Purchase Hardware = |Design Files = [https://github.com/newaetech/chipwhisperer/tree/master/hardware/victims/cw308_ufo_target/d2000 GITHub link]
See [https://oshparkrtfm.newae.com/shared_projectsTargets/HOs4WL4l OSH Park PCBsUFO%20Targets/CW308T-D2000/ NewAE RTFM Page]which is now built from the [https://github.com/newaetech/chipwhisperer-target-cw308t GIT Repo].
|Supported Applications =}}  The D2000 target is a bit of an oddball. It's an x86 target, but is really a microcontroller (internal flash etc).  == Using Board == The CW308T-D2000 is used similar to any other CW308 Target Board. It does not accept an external oscillator, instead it outputs it's own oscillator for you to synchronize to. Specific caveats here: * Be sure to mount J3 at lowest setting which routes the "CLKFB" line to "HS1/IN".* You'll need to configure the ChipWhisperer to use an external clock input (EXTCLK or EXTCLK x4). This is taken care of by the D2000 setup script.* The baud rate will need to be changed - it is scaled to be 115200 at 32 MHz. Use the frequency counter to measure the actual frequency & scale baud rate appropriately. Depending previous content on the ROM loaded the clock varies. This is taken care of by the D2000 setup script.* The TX/RX are opposite compared to the XMEGA. This is taken care of by the D2000 setup script. The following shows an example setup script for this board: <syntaxhighlight lang="python">scope.gain.gain = 45scope.adc.samples = 25000scope.adc.offset = 0scope.adc.basic_mode = "rising_edge"scope.clock.clkgen_freq = 7370000scope.clock.adc_src = "extclk_x4"scope.trigger.triggers = "tio4"#TX/RX backwards from XMEGAscope.io.tio1 = "serial_tx"scope.io.tio2 = "serial_rx"scope.io.hs2 = None # Sample delay - you may need wiki has been moved to increase this!# Gives time for frequency measurement to occur in hardware.time.sleep(0.5) ext_freq = scope.clock.freq_ctr if ext_freq > 10:  baud = (115200 / 32E6) * ext_freq print "Based on extclk of %d Hz, setting baud to %d" % (ext_freq, baud) target.baud = baud else: raise IOError("Did not detect external clock from D2000. Confirm jumpers and rerun, or increase delay before sample."</syntaxhighlight> == Building Firmware ==To build firmware for the D2000, you'll need to download the [https://software.intel.com/en-us/articles/issm-toolchain-only-download Intel ISSM Toolchain] and uncompress it. The toolchain comes compressed/archived in the tar.gz format, so you may need to download a program that can work with those formats (such as 7-zip on Windows). Firmware is contained in <code>hardware/victims/firmware/intel_quark/simpleserial_example/</code> and can be built with make. Note that you'll need to specify where the toolchain is located: === Specifying Toolchain Location ===If you're using <code>cmd</code> on Windows (as opposed to something like <code>Git Bash</code> or <code>Cygwin</code>, you'll need to create a new environment variable called <code>IAMCU_TOOLCHAIN_DIR</code> and set its value to the path to the toolchain. For example, I uncompressed the toolchain to <code>C:\Users\User\Downloads</code> and set the variable to <code>C:\Users\User\Downloads\issm-toolchain-windows-2017-01-25\tools\compiler\gcc-ia\5.2.1\bin</code>. Otherwise, running <code>export /path/to/toolchain/bin</code> should work on Mac, Linux, Git Bash, Cygwin, etc. === Troubleshooting ===* No such file or directory when building on Windows** This is usually caused by the default make directory command (<code>md</code>) not working. First, ensure that you have <code>mkdir</code> and cp on your system by opening <code>cmd</code> and running them. Then open <code>hardware/victims/firmware/intel_quark/qmsi/base.mk</code> and change:<syntaxhighlight lang="makefile"># Any other version of Windowsmkdir = @md $(subst /,\,$(1)) > nul 2>&1 || exit 0copy = @copy $(subst /,\,$(1)) $(subst /,\,$(2)) > nul 2>&1 || exit 0</syntaxhighlight>to:<syntaxhighlight lang="makefile"># Any other version of Windowsmkdir = @mkdir -p $(1) || exit 0copy = @cp $(1) $(2) || exit 0</syntaxhighlight> == Programming == An external programmer is needed for this target. The Quark D2000 dev-board can be used with jumper wires, or a standard OpenOCD programmer can be used. The suggested programmer is the [https://mouser.com/ProductDetail/Olimex-Ltd/ARM-USB-OCD-H Olimex ARM-USB-OCD-H] as is available from suppliers such as Mouser and Digi-Key (mouser above link provided){{Warningbox|The D2000 chips have a weird combination of what they call "ROM" (actually not ROM remotely) and application space. When building See wiki history if you normally use the D2000 ROM provided (or can build your own). However you only need to program this section the first time - it is not recommended to reprogram it unless needed, since it is possible to brick the D2000 with a corrupt ROM load. The D2000 boards come loaded with an example ROM & application as well already.}} === OpenOCD Board Setup === If using OpenOCD either stand-alone or as part of Intel ISSM, you'll need to define a new board file. The file is based on <code>scripts\board\quark_d2000.cfg</code> found in the following directory: <code>C:\IntelSWTools\ISSM_2016.0.027\tools\debugger\openocd\scripts\board</code> (adjust for version number changes). You will find a line would like the following in the original file:  #default frequency but this can be adjusted at runtime adapter_khz 1000 Make a copy of the file, but change that to a slower speed (suggested is 125 kHz)  #default frequency but this can be adjusted at runtime adapter_khz 125 Save this file as <code>quark_d2000_ufo.cfg</code>. === How to flash D2000 board using OpenOCD === We'll modify the provided scripts from the Intel ISSM distribution (compiler etc for D2000). Start a Windows command prompt and run the following commands. You may have to change the directory view exact older versions of the first command to match your version of Intel ISSM (eg. C:\IntelSWTools\ISSM_2016.0.027\issm_env.bat):  C:\IntelSWTools\ISSM_2016.2.097\issm_env.bat cd %ISSM_DEBUGGER_ROOT%\openocd bin\openocd.exe -f scripts\interface\ftdi\olimex-arm-usb-ocd-h.cfg -f scripts\board\quark_d2000_ufo.cfg  Note we specify two script files - the first had the JTAG connection (the olimex-arm-usb-ocd-h.cfg), the second had the D2000. This should result in an output like the following:  Open On-Chip Debugger 0.8.0-dev-g7845893 (2015-11-26-18:12) Licensed under GNU GPL v2 For bug reports, read http://openocd.sourceforge.net/doc/doxygen/bugs.html Info : only one transport option; autoselect 'jtag' adapter speed: 125 kHz trst_only separate trst_push_pull flash_rom Info : clock speed 125 kHz Info : JTAG tap: quark_d2000.cltap tap/device found: 0x0e786013 (mfg: 0x009, part: 0xe786, ver: 0x0) Enabling lmt core tap Info : JTAG tap: quark_d2000.lmt enabled {{Warningbox|If you get errors here, confirm the JTAG clock speed is not running too quickly. You need to modify the example script file to slow down the JTAG speed for this board (due to shunt resistor inline with VCC-core).}} At this point it will hold, waiting for new commands. There is two ways to proceed: ==== Connecting with GDB ==== Connecting and programming with GDB may be preferred if you wish to also do any debug. It however is more limited in what commands you can run. If this does not work see the next section about using telnet commands. Open a second command prompt, and run:  C:\IntelSWTools\ISSM_2016.0.027\issm_env.bat gdb You can then run the following within a GDB console:  target remote :3333 monitor clk32M 125 monitor load_image C:\\chipwhisperer\\hardware\\victims\\firmware\\intel_quark\\quark_d2000_rom.bin 0x0 monitor load_image C:\\chipwhisperer\\hardware\\victims\\firmware\\intel_quark\\simpleserial_example\\release\\quark_d2000\\x86\\bin\\simpleserial_aes.bin 0x00180000 The first load_image is used for the ROM image. This should only be done once - do not reload every time, only reload the application. The boards as shipped come with a ROM image so you can skip that step if using the NewAE example code. Notes: # The <code>monitor clk32M 125</code> sets a 125 kHz JTAG clock frequency. This may be too slow, but is recommended especially when loading ROM due to potential for misprogramming on the target board due to the shunt resistor. Note it takes a long time (~60 seconds) to program the ROM code so don't abort it!# If the above fails, see the next note on recovering normal settings with the telnet interface.# You can short F13 (GPIO1 on the ChipWhisperer-Lite) to GND to force the JTAG pins on. It is suggested to do this via the ChipWhisperer-Lite software (setting it as a GPIO output and then setting it low). This requires the 'ROM' code programmed in already.# Do not reload the ROM code unless needed -- this is the boot code and if something gets corrupt it can brick the device. ==== Connecting with Telnet to Monitor ==== When running the <code>target remote :3333</code> or other commands above, you may encounter errors that seem fatal. Do not fret, you can likely recover everything using another mode. To do so: # Power cycle the target board, and re-run the openocd command previously specified (assuming you have encountered errors and the system is in an unknown state).# If this fails, set GPIO1 to LOW, and power cycle the target. Try connecting again. Assuming the connect works, open a second command prompt and run  telnet localhost 4444 Note the port connected to is 4444 (not :3333) as before. This now enters the monitor directly, and you can try running the following commands:  reset halt set QUARK_D2000_OTPC_DATA_WRITE_ENABLED 1 mass_erase clk32M 100 load_image C:\\chipwhisperer\\hardware\\victims\\firmware\\intel_quark\\quark_d2000_rom.bin 0x0 load_image C:\\chipwhisperer\\hardware\\victims\\firmware\\intel_quark\\simpleserial_example\\release\\quark_d2000\\x86\\bin\\simpleserial_aes.bin 0x00180000 The following should be the example output of these commands:  > reset halt JTAG tap: quark_d2000.cltap tap/device found: 0x0e786013 (mfg: 0x009, part: 0xe786, ver: 0x0) Enabling lmt core tap JTAG tap: quark_d2000.lmt enabled target state: halted target halted due to debug-request at 0x0000ffff in real mode target state: halted target halted due to debug-request at 0x0000fff0 in real mode > set QUARK_D2000_OTPC_DATA_WRITE_ENABLED 1 1 > mass_erase Deleting OTPC, OTPD and FLASH regions 0xb0100014: 00000001 > clk32M 100 adapter speed: 3 kHz adapter speed: 100 kHz JTAG tap: quark_d2000.cltap tap/device found: 0x0e786013 (mfg: 0x009, part: 0xe786, ver: 0x0) Enabling lmt core tap JTAG tap: quark_d2000.lmt enabled target state: halted target halted due to debug-request at 0x0000fff0 in real mode > load_image C:\\chipwhisperer\\hardware\\victims\\firmware\\intel_quark\\quark_d2000_rom.bin 0x0 ....8192 bytes written at address 0x00000000 downloaded 8192 bytes in 66.997505s (0.119 KiB/s) > load_image C:\\chipwhisperer\\hardware\\victims\\firmware\\intel_quark\\simpleserial_example\\release\\quark_d2000\\x8 .2872 bytes written at address 0x00180000 downloaded 2872 bytes in 42.280869s (0.066 KiB/s) Note you can try the following if still having trouble: # Use a slower JTAG clock speed. Be SURE you are using a custom .cfg file which specifies the slower JTAG speed on initial connect (and not just as part of the clk32M commands).# Short the SHUNTH/SHUNTL pins. == Schematic == See GIT Repo for PDF of schematic. Note there is a new "03C" rev that changes the shunt resistor (R1) to a 1-ohm resistor. This results in a much more reliable device, as the original 10-ohm shunt caused occasional crashes. If you are using an older revision device, you can mount a shunt/jumper between "SH-" and "SH+" on the UFO board to achieve a similar effect. [[File:CW308T-D2000-02_schematic.png|1000px]] == Board Layout == See GIT Repo for gerber filespage== Hardware == {{Template:Hardware}}[[Category:CW308 Targets]]
Approved_users, bureaucrat, administrator
1,956
edits

Navigation menu