|As of August 2020 the site you are on (wiki.newae.com) is deprecated, and content is now at rtfm.newae.com.|
Correlation Power Analysis
Correlation Power Analysis (CPA) is an attack that allows us to find a secret encryption key that is stored on a victim device. There are 4 steps to a CPA attack:
- Write down a model for the victim's power consumption. This model will look at one specific point in the encryption algorithm. (ie: after step 2 of the encryption process, the intermediate result is , so the power consumption is .)
- Get the victim to encrypt several different plaintexts. Record a trace of the victim's power consumption during each of these encryptions.
- Attack small parts (subkeys) of the secret key:
- Consider every possible option for the subkey. For each guess and each trace, use the known plaintext and the guessed subkey to calculate the power consumption according to our model.
- Calculate the Pearson correlation coefficient between the modeled and actual power consumption. Do this for every data point in the traces.
- Decide which subkey guess correlates best to the measured traces.
- Put together the best subkey guesses to obtain the full secret key.
This page discusses some of the basics of these steps, describing what models are typically used in CPA attacks and how the Pearson correlation coefficient is calculated.
Modeling Power Consumption
Electronic computers (microcontrollers, FPGAs, etc) have two components to their power consumption. First, static power consumption is the power required to keep the device running. This static power depends on things like the number of transistors inside the device. Secondly, and more importantly, dynamic power consumption depends on the data moving around inside the device. Every time a bit is changed from a 0 to a 1 (or vice versa), some current is required to (dis)charge the data lines. The dynamic power is the part that we're interested in - it can tell us what's happening inside.
One of the simplest models for power consumption is the Hamming Distance model. The Hamming Distance between two binary numbers is the number of different bits in the numbers. For example,
HammingDistance(00110000, 00100011) = 3
because there are 3 unequal bits in these two numbers. An easy way to calculate the Hamming Distance is
HammingDistance(x, y) = HammingWeight(x ^ y)
^ is the XOR operator, and the Hamming Weight is the number of 1s in a binary number. Using the example above,
HammingDistance(00110000, 00100011) = HammingWeight(00010011) = 3
00010011 has three bits set.
We can use the Hamming Distance model in our CPA attacks. If we can find a point in the encryption algorithm where the victim changes a variable from
y, then we can estimate that the power consumption is proportional to
Hamming Distance(x, y). Often, our model can even be a bit simpler: if we assume that the victim is replacing the value
x = 0, then our power model is
l(y) = HammingWeight(y)
Pearson's Correlation Coefficient
Once we have a way to model our power consumption, we need a way to compare our power estimate to our measured traces. A helpful tool for finding this relationship is through Pearson's correlation coefficient, which is
This correlation coefficient will always be in the range [-1, 1]. It describes how closely the random variables and are related:
- If always increases when increases, it will be 1;
- If always decreases when increases, it will be -1;
- If is totally independent of , it will be 0.
These equations are referred to as the normalized cross-correlation. There are typically used to pick out patterns in noisy signals. For example, in digital imaging, correlation can be used to find where an object is in a room. In our attack, we'll be looking for a our model (a pre-calculated pattern) in measured power traces (noisy signals).
Attacking with Correlation
After taking our measurements, we'll have power traces , and each of these traces will have data points. Using subscript notation, will refer to point in trace ().
We'll also estimate the power consumption in each trace using our model. We'll say that there are different subkeys that we want to try. Then, will refer to our power estimate in trace , assuming that the subkey is ().
With this data, we can see how well our model and measurements match for each guess and time . We'll do this by finding how and correlate over the traces. One way of calculating this is:
There is an alternative form of the correlation equation that we can use for online calculations - it allows us to add one trace at a time without re-summing all of the past data. This form is:
Note that these two sums are equivalent.
Picking a Subkey
The last step is to use the values of to decide which subkey matches our traces most closely. There are two steps to this:
- For each subkey , find the highest value of . This will discard the time information - we want to know how good our guess was, but we don't care where our guess matched the trace.
- Looking at the maximum values for each subkey, find the highest value of . The location of this maximum is our best guess: it correlated more closely with the traces than any other guess.
Note that we're only working with absolute values here because we don't care about the sign of the relationship. All we need to know is that a linear correlation exists.
As an example, consider AES-128 encryption. The pseudo-code for this algorithm is:
// AES-128 Cipher // in: 128 bits (plaintext) // out: 128 bits (ciphertext) // w: 44 words, 32 bits each (expanded key) state = in AddRoundKey(state, w[0, Nb-1]) for round = 1 step 1 to Nr–1 SubBytes(state) // <-- Attack this point in round 1! ShiftRows(state) MixColumns(state) AddRoundKey(state, w[round*Nb, (round+1)*Nb-1]) end for SubBytes(state) ShiftRows(state) AddRoundKey(state, w[Nr*Nb, (Nr+1)*Nb-1]) out = state
This might look pretty complex, but we only need to worry about one part of the algorithm. After the first
SubBytes() step, the state is effectively
// State after AddRoundKey() and SubBytes() state = sbox[in ^ key]
sbox is a lookup table used in AES. This is an effective point to attack. If we know that a byte of the plaintext is , then our modeled power consumption will be
Then, we can proceed with the attack as described above. Since we are attacking one byte of the key at a time, we will have to try values for each subkey. Then, there are 16 bytes in the key, so our attack will take time. This is an enormous improvement over trying every possible key, which would take time.