Bootloader Communications Protocol

The bootloader's communications protocol operates over a serial port at 38400 baud rate. The bootloader is always waiting for new data to be sent in this example; in real life one would typically force the bootloader to enter through a command sequence.

Commands sent to the bootloader look as follows:

       |<-------- Encrypted block (16 bytes) ---------->|
       |                                                |
+------+------+------+------+------+------+ .... +------+------+------+
| 0x00 |    Signature (4 Bytes)    |  Data (12 Bytes)   |   CRC-16    |
+------+------+------+------+------+------+ .... +------+------+------+

This frame has four parts:

• 0x00: 1 byte of fixed header
• Signature: A secret 4 byte constant. The bootloader will confirm that this signature is correct after decrypting the frame.
• Data: 12 bytes of the incoming firmware. This system forces us to send the code 12 bytes at a time; more complete bootloaders may allow longer variable-length frames.
• CRC-16: A 16-bit checksum using the CRC-CCITT polynomial (0x1021). The LSB of the CRC is sent first, followed by the MSB. The bootloader will reply over the serial port, describing whether or not this CRC check was valid.

As described in the diagram, the 16 byte block is not sent as plaintext. Instead, it is encrypted using AES-256 in CBC mode. This encryption method will be described in the next section.

The bootloader responds to each command with a single byte indicating if the CRC-16 was OK or not:

            +------+
CRC-OK:     | 0xA1 |
            +------+

            +------+
CRC Failed: | 0xA4 |
            +------+

Then, after replying to the command, the bootloader veries that the signature is correct. If it matches the expected manufacturer's signature, the 12 bytes of data will be written to flash memory. Otherwise, the data is discarded.

Details of AES-256 CBC

The system uses the AES algorithm in Cipher Block Chaining (CBC) mode. In general one avoids using encryption 'as-is' (i.e. Electronic Code Book), since it means any piece of plaintext always maps to the same piece of ciphertext. Cipher Block Chaining ensures that if you encrypted the same thing a bunch of times it would always encrypt to a new piece of ciphertext.

You can see another reference on the design of the encryption side; we'll be only talking about the decryption side here. In this case AES-256 CBC mode is used as follows, where the details of the AES-256 Decryption block will be discussed in detail later:

This diagram shows that the output of the decryption is no longer used directly as the plaintext. Instead, the output is XORed with a 16 byte mask, which is usually taken from the previous ciphertext. Also, the first decryption block has no previous ciphertext to use, so a secret initialization vector (IV) is used instead. If we are going to decrypt the entire ciphertext (including block 0) or correctly generate our own ciphertext, we'll need to find this IV along with the AES key.

Attacking AES-256

The system in this tutorial uses AES-256 encryption, which has a 256 bit (32 byte) key - twice as large as the 16 byte key we've attacked in previous tutorials. This means that our regular AES-128 CPA attacks won't quite work. However, extending these attacks to AES-256 is fairly straightforward: the theory is explained in detail in Extending AES-128 Attacks to AES-256.

As the theory page explains, our AES-256 attack will have 4 steps:

1. Perform a standard attack (as in AES-128 decryption) to determine the first 16 bytes of the key, corresponding to the 14th round encryption key.
2. Using the known 14th round key, calculate the hypothetical outputs of each S-Box from the 13th round using the ciphertext processed by the 14th round, and determine the 16 bytes of the 13th round key manipulated by inverse MixColumns.
3. Perform the MixColumns and ShiftRows operation on the hypothetical key determined above, recovering the 13th round key.
4. Using the AES-256 key schedule, reverse the 13th and 14th round keys to determine the original AES-256 encryption key.

Setting up the Hardware

This tutorial uses the CW1002_ChipWhisperer_Capture_Rev2 hardware along with the CW301_Multi-Target board. Note that you don't need hardware to complete the tutorial. Instead you can download example traces from the ChipWhisperer Site, just look for the traces titled AVR: AES256 Bootloader (ChipWhisperer Tutorial #A5).

This example uses the Atmel AVR in 28-pin DIP programmed with a demo bootloader. You can see instructions for programming in the Installing ChipWhisperer section, this tutorial assumes you have the programmer aspect working.

The Multi-Target board should be plugged into the ChipWhisperer Capture Rev2 via the 20-pin target cable. The VOUT SMA connector is wired to the LNA input on the ChipWhisperer-Capture Rev2 front panel. The general hardware setup is as follows:

1. 20-Pin Header connects Multi-Target to Capture Hardware
2. VOUT Connects to SMA Cable
3. SMA Cable connects to 'LNA' on CHA input
4. USB-Mini connects to side (NB: Confirm jumper settings in next section first)

Jumpers on the Multi-Target Victim board are as follows:

1. NO jumpers mounted in XMEGA Portion or SmartCard Portion (JP10-JP15, JP19, JP7-JP8, JP17)
2. 3.3V IO Level (JP20 set to INT.)
3. The 7.37 MHz oscillator is selected as the CLKOSC source (JP18)
4. The CLKOSC is connected to the AVR CLock Network, along with connected to the FPGAIN pin (JP4)
5. The TXD & RXD jumpers are set (JP5, JP6)
6. Power measurement taken from VCC shunt (JP1)
7. The TRIG jumper is set (JP28) (NOTE: Early revisions of the multi-target board do not have the TRIG jumper and you can ingore this).

For more information on these jumper settings see CW301_Multi-Target .

Capturing the Traces

It is assumed that you've already followed the guide in Installing ChipWhisperer. Thus it is assumed you are able to communicate with the ChipWhisperer Capture Rev2 hardware (or whatever capture hardware you are using). Note in particular you must have configured the FPGA bitstream in the ChipWhisperer-Capture software, all part of the description in the Installing ChipWhisperer guide.

Analyzing of Power Traces for Key

warning

The API calling parameters changed in release 0.10 of the ChipWhisperer software. If using 0.09 release or older, see the documentation that

is present in the 'doc' directory (which will always correspond to your release).

# Imports for AES256 Attack
from chipwhisperer.analyzer.attacks.models.AES128_8bit import getHW
from chipwhisperer.analyzer.models.aes.funcs import sbox, inv_sbox, inv_shiftrows, inv_mixcolumns, inv_subbytes

class AES256Attack(object):
    numSubKeys = 16

    @staticmethod
    def leakage(textin, textout, guess, bnum, setting, state):
        if setting == 13:
           knownkey = [0xea, 0x79, 0x79, 0x20, 0xc8, 0x71, 0x44, 0x7d, 0x46, 0x62, 0x5f, 0x51, 0x85, 0xc1, 0x3b, 0xcb]
           xored = [knownkey[i] ^ textin[i] for i in range(0, 16)]
           block = xored
           block = inv_shiftrows(block)
           block = inv_subbytes(block)
           block = inv_mixcolumns(block)
           block = inv_shiftrows(block)
           result = block
           return getHW(inv_sbox((result[bnum] ^ guess)))

>>> from chipwhisperer.analyzer.models.aes.funcs import shiftrows,mixcolumns
>>> knownkey = [0xC6, 0xBD, 0x4E, 0x50, 0xAB, 0xCA, 0x75, 0x77, 0x79, 0x87, 0x96, 0xCA, 0x1C, 0x7F, 0xC5, 0x82]
>>> key = shiftrows(knownkey)
>>> key = mixcolumns(key)
>>> print " ".join(["%02x" % i for i in key])
c6 6a a6 12 4a ba 4d 04 4a 22 03 54 5b 28 0e 63

c6 6a a6 12 4a ba 4d 04 4a 22 03 54 5b 28 0e 63 ea 79 79 20 c8 71 44 7d 46 62 5f 51 85 c1 3b cb

94 28 5d 4d 6d cf ec 08 d8 ac dd f6 be 25 a4 99 c4 d9 d0 1e c3 40 7e d7 d5 28 d4 09 e9 f0 88 a1

Analysis of Encrypted Files

TODO

Analysis of Power Traces for IV

TODO

Example:

#Imports for IV Attack
from Crypto.Cipher import AES

def initPreprocessing(self):
    self.preProcessingResyncSAD0 = preprocessing.ResyncSAD.ResyncSAD(self.parent)
    self.preProcessingResyncSAD0.setEnabled(True)
    self.preProcessingResyncSAD0.setReference(rtraceno=0, refpoints=(6300,6800), inputwindow=(6000,7200))
    self.preProcessingResyncSAD1 = preprocessing.ResyncSAD.ResyncSAD(self.parent)
    self.preProcessingResyncSAD1.setEnabled(True)
    self.preProcessingResyncSAD1.setReference(rtraceno=0, refpoints=(4800,5100), inputwindow=(4700,5200))
    self.preProcessingList = [self.preProcessingResyncSAD0,self.preProcessingResyncSAD1,]
    return self.preProcessingList

class AESIVAttack(object):
   numSubKeys = 16

   @staticmethod
   def leakage(textin, textout, guess, bnum, setting, state):
       knownkey = [0x94, 0x28, 0x5D, 0x4D, 0x6D, 0xCF, 0xEC, 0x08, 0xD8, 0xAC, 0xDD, 0xF6, 0xBE, 0x25, 0xA4, 0x99,
                   0xC4, 0xD9, 0xD0, 0x1E, 0xC3, 0x40, 0x7E, 0xD7, 0xD5, 0x28, 0xD4, 0x09, 0xE9, 0xF0, 0x88, 0xA1]
       knownkey = str(bytearray(knownkey))
       ct = str(bytearray(textin))

       aes = AES.new(knownkey, AES.MODE_ECB)
       pt = aes.decrypt(ct)
       return getHW(bytearray(pt)[bnum] ^ guess)

Timing Attacks for Signature

Appendix A Capture Script

The following:

#!/usr/bin/python
# -*- coding: utf-8 -*-
#
# Copyright (c) 2013-2014, NewAE Technology Inc
# All rights reserved.
#
# Authors: Colin O'Flynn
#
# Find this and more at newae.com - this file is part of the chipwhisperer
# project, http://www.assembla.com/spaces/chipwhisperer
#
#    This file is part of chipwhisperer.
#
#    chipwhisperer is free software: you can redistribute it and/or modify
#    it under the terms of the GNU General Public License as published by
#    the Free Software Foundation, either version 3 of the License, or
#    (at your option) any later version.
#
#    chipwhisperer is distributed in the hope that it will be useful,
#    but WITHOUT ANY WARRANTY; without even the implied warranty of
#    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
#    GNU Lesser General Public License for more details.
#
#    You should have received a copy of the GNU General Public License
#    along with chipwhisperer.  If not, see <http://www.gnu.org/licenses/>.
#=================================================
#
#
#
# This example captures data using the ChipWhisperer Rev2 capture hardware.
# The target is a SimpleSerial board attached to the ChipWhisperer.
#
# Data is saved into both a project file and a MATLAB array
#

#Setup path
import sys

import time

#Import the ChipWhispererCapture module
import chipwhisperer.capture.ChipWhispererCapture as cwc
from chipwhisperer.capture.targets.TargetTemplate import TargetTemplate
from chipwhisperer.capture.targets.SimpleSerial import SimpleSerial_ChipWhisperer

#Check for PySide
try:
    from PySide.QtCore import *
    from PySide.QtGui import *
except ImportError:
    print "ERROR: PySide is required for this program"
    sys.exit()

import thread

import scipy.io as sio

exitWhenDone=False

def pe():
    QCoreApplication.processEvents()

# Class Crc
#############################################################
# These CRC routines are copy-pasted from pycrc, which are:
# Copyright (c) 2006-2013 Thomas Pircher <tehpeh@gmx.net>
#
class Crc(object):
    """
    A base class for CRC routines.
    """

    def __init__(self, width, poly):
        """The Crc constructor.

        The parameters are as follows:
            width
            poly
            reflect_in
            xor_in
            reflect_out
            xor_out
        """
        self.Width = width
        self.Poly = poly


        self.MSB_Mask = 0x1 << (self.Width - 1)
        self.Mask = ((self.MSB_Mask - 1) << 1) | 1

        self.XorIn = 0x0000
        self.XorOut = 0x0000

        self.DirectInit = self.XorIn
        self.NonDirectInit = self.__get_nondirect_init(self.XorIn)
        if self.Width < 8:
            self.CrcShift = 8 - self.Width
        else:
            self.CrcShift = 0

    def __get_nondirect_init(self, init):
        """
        return the non-direct init if the direct algorithm has been selected.
        """
        crc = init
        for i in range(self.Width):
            bit = crc & 0x01
            if bit:
                crc ^= self.Poly
            crc >>= 1
            if bit:
                crc |= self.MSB_Mask
        return crc & self.Mask


    def bit_by_bit(self, in_data):
        """
        Classic simple and slow CRC implementation.  This function iterates bit
        by bit over the augmented input message and returns the calculated CRC
        value at the end.
        """
        # If the input data is a string, convert to bytes.
        if isinstance(in_data, str):
            in_data = [ord(c) for c in in_data]

        register = self.NonDirectInit
        for octet in in_data:
            for i in range(8):
                topbit = register & self.MSB_Mask
                register = ((register << 1) & self.Mask) | ((octet >> (7 - i)) & 0x01)
                if topbit:
                    register ^= self.Poly

        for i in range(self.Width):
            topbit = register & self.MSB_Mask
            register = ((register << 1) & self.Mask)
            if topbit:
                register ^= self.Poly

        return register ^ self.XorOut

class BootloaderTarget(TargetTemplate):
    paramListUpdated = Signal(list)

    def setupParameters(self):
        self.ser = SimpleSerial_ChipWhisperer()
        self.keylength = 16
        self.input = ""
        self.crc = Crc(width=16, poly=0x1021)

    def setOpenADC(self, oadc):
        try:
            self.ser.setOpenADC(oadc)
        except:
            pass

    def setKeyLen(self, klen):
        """ Set key length in BITS """
        self.keylength = klen / 8

    def keyLen(self):
        """ Return key length in BYTES """
        return self.keylength


    def paramList(self):
        return []

    def con(self):
        self.ser.con()
        self.ser.flush()

    def dis(self):
        self.close()

    def close(self):
        if self.ser != None:
            self.ser.close()
            self.ser = None
        return

    def init(self):
        pass

    def setModeEncrypt(self):
        return

    def setModeDecrypt(self):
        return

    def loadEncryptionKey(self, key):
        pass

    def loadInput(self, inputtext):
        self.input = inputtext

    def isDone(self):
        return True

    def readOutput(self):
        #No actual output
        return [0] * 16

    def go(self):
        # Starting byte is 0x00
        message = [0x00]

        # Append 16 bytes of data
        message.extend(self.input)

        # Append 2 bytes of CRC for input only (not including 0x00)
        crcdata = self.crc.bit_by_bit(self.input)

        message.append(crcdata >> 8)
        message.append(crcdata & 0xff)

        # Write message
        for i in range(0, 5):
            self.ser.flush()
            self.ser.write(message)
            time.sleep(0.1)
            data = self.ser.read(1)

            if len(data) > 0:
                resp = ord(data[0])

                if resp == 0xA4:
                    # Encryption run OK
                    break

                if resp != 0xA1:
                    raise IOError("Bad Response %x" % resp)

        if len(data) > 0:
            if resp != 0xA4:
                raise IOError("Failed to communicate, last response: %x" % resp)
        else:
            raise IOError("Failed to communicate, no response")

    def checkEncryptionKey(self, kin):
        return kin

class userScript(QObject):

    def __init__(self, capture):
        super(userScript, self).__init__()
        self.capture = capture


    def run(self):
        cap = self.capture

        #User commands here
        print "***** Starting User Script *****"

        tbootloader = BootloaderTarget()

        cap.setParameter(['Generic Settings', 'Scope Module', 'ChipWhisperer/OpenADC'])
        cap.setParameter(['Generic Settings', 'Trace Format', 'ChipWhisperer/Native'])

        cap.target.setDriver(tbootloader)

        #Load FW (must be configured in GUI first)
        cap.FWLoaderGo()

        #NOTE: You MUST add this call to pe() to process events. This is done automatically
        #for setParameter() calls, but everything else REQUIRES this
        pe()

        cap.doConDis()

        pe()

        #Example of using a list to set parameters. Slightly easier to copy/paste in this format
        lstexample = [['CW Extra', 'CW Extra Settings', 'Trigger Pins', 'Front Panel A', False],
                      ['CW Extra', 'CW Extra Settings', 'Trigger Pins', 'Target IO4 (Trigger Line)', True],
                      ['CW Extra', 'CW Extra Settings', 'Clock Source', 'Target IO-IN'],
                      ['OpenADC', 'Clock Setup', 'ADC Clock', 'Source', 'EXTCLK x4 via DCM'],
                      ['OpenADC', 'Trigger Setup', 'Total Samples', 11000],
                      ['OpenADC', 'Trigger Setup', 'Offset', 0],
                      ['OpenADC', 'Gain Setting', 'Setting', 45],
                      ['OpenADC', 'Trigger Setup', 'Mode', 'rising edge'],
                      #Final step: make DCMs relock in case they are lost
                      ['OpenADC', 'Clock Setup', 'ADC Clock', 'Reset ADC DCM', None],

                      ['Generic Settings', 'Auxilary Module', 'Toggle FPGA-GPIO Pins'],
                      ['GPIO Toggle', 'Standby State', 'High'],
                      ['GPIO Toggle', 'Post-Toggle Delay', 150],
                      ['GPIO Toggle', 'Toggle Length', 100],
                      ]

        # For IV: offset = 70000

        #Download all hardware setup parameters
        for cmd in lstexample: cap.setParameter(cmd)

        #Let's only do a few traces
        cap.setParameter(['Generic Settings', 'Acquisition Settings', 'Number of Traces', 50])

        #Throw away first few
        cap.capture1()
        pe()
        cap.capture1()
        pe()

        print "***** Ending User Script *****"


if __name__ == '__main__':
    #Make the application
    app = cwc.makeApplication()

    #If you DO NOT want to overwrite/use settings from the GUI version including
    #the recent files list, uncomment the following:
    #app.setApplicationName("Capture V2 Scripted")

    #Get main module
    capture = cwc.ChipWhispererCapture()

    #Show window - even if not used
    capture.show()

    #NB: Must call processEvents since we aren't using proper event loop
    pe()
    # Call user-specific commands
    usercommands = userScript(capture)

    usercommands.run()

    app.exec_()

    sys.exit()

Appendix B AES-256 14th Round Key Script

NB: This script works for 0.10 release or later, see local copy in doc/html directory of chipwhisperer release if you need earlier versions

Full attack script, copy/paste into a file then add as active attack script:

# AES-256 14th Round Key Attack
from chipwhisperer.common.autoscript import AutoScriptBase
#Imports from Preprocessing
import chipwhisperer.analyzer.preprocessing as preprocessing
#Imports from Capture
from chipwhisperer.analyzer.attacks.CPA import CPA
from chipwhisperer.analyzer.attacks.CPAProgressive import CPAProgressive
import chipwhisperer.analyzer.attacks.models.AES128_8bit
#Imports from utilList

class userScript(AutoScriptBase):
    preProcessingList = []
    def initProject(self):
        pass

    def initPreprocessing(self):
        self.preProcessingList = []
        return self.preProcessingList

    def initAnalysis(self):
        self.attack = CPA(self.parent, console=self.console, showScriptParameter=self.showScriptParameter)
        self.attack.setAnalysisAlgorithm(CPAProgressive,chipwhisperer.analyzer.attacks.models.AES128_8bit,chipwhisperer.analyzer.attacks.models.AES128_8bit.LEAK_HW_INVSBOXOUT_FIRSTROUND)
        self.attack.setTraceStart(0)
        self.attack.setTracesPerAttack(99)
        self.attack.setIterations(1)
        self.attack.setReportingInterval(10)
        self.attack.setTargetBytes([0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15])
        self.attack.setTraceManager(self.traceManager())
        self.attack.setProject(self.project())
        self.attack.setPointRange((0,10992))
        return self.attack

    def initReporting(self, results):
        results.setAttack(self.attack)
        results.setTraceManager(self.traceManager())
        self.results = results

    def doAnalysis(self):
        self.attack.doAttack()

Appendix C AES-256 13th Round Key Script

NB: This script works for 0.10 release or later, see local copy in doc/html directory of chipwhisperer release if you need earlier versions

Full attack script, copy/paste into a file then add as active attack script:

# AES-256 13th Round Key Script
from chipwhisperer.common.autoscript import AutoScriptBase
#Imports from Preprocessing
import chipwhisperer.analyzer.preprocessing as preprocessing
#Imports from Capture
from chipwhisperer.analyzer.attacks.CPA import CPA
from chipwhisperer.analyzer.attacks.CPAProgressive import CPAProgressive
import chipwhisperer.analyzer.attacks.models.AES128_8bit
# Imports from utilList

# Imports for AES256 Attack
from chipwhisperer.analyzer.attacks.models.AES128_8bit import getHW
from chipwhisperer.analyzer.models.aes.funcs import sbox, inv_sbox, inv_shiftrows, inv_mixcolumns, inv_subbytes

class AES256Attack(object):
   numSubKeys = 16

   @staticmethod
   def leakage(textin, textout, guess, bnum, setting, state):
       if setting == 13:
          knownkey = [0xea, 0x79, 0x79, 0x20, 0xc8, 0x71, 0x44, 0x7d, 0x46, 0x62, 0x5f, 0x51, 0x85, 0xc1, 0x3b, 0xcb]
          xored = [knownkey[i] ^ textin[i] for i in range(0, 16)]
          block = xored
          block = inv_shiftrows(block)
          block = inv_subbytes(block)
          block = inv_mixcolumns(block)
          block = inv_shiftrows(block)
          result = block
          return getHW(inv_sbox((result[bnum] ^ guess)))

class userScript(AutoScriptBase):
   preProcessingList = []
   def initProject(self):
       pass

   def initPreprocessing(self):
       self.preProcessingResyncSAD0 = preprocessing.ResyncSAD.ResyncSAD(self.parent)
       self.preProcessingResyncSAD0.setEnabled(True)
       self.preProcessingResyncSAD0.setReference(rtraceno=0, refpoints=(9063,9177), inputwindow=(9010,9180))
       self.preProcessingList = [self.preProcessingResyncSAD0,]
       return self.preProcessingList

   def initAnalysis(self):
       self.attack = CPA(self.parent, console=self.console, showScriptParameter=self.showScriptParameter)
       self.attack.setAnalysisAlgorithm(CPAProgressive, AES256Attack, 13)
       self.attack.setTraceStart(0)
       self.attack.setTracesPerAttack(100)
       self.attack.setIterations(1)
       self.attack.setReportingInterval(25)
       self.attack.setTargetBytes([0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15])
       self.attack.setTraceManager(self.traceManager())
       self.attack.setProject(self.project())
       self.attack.setPointRange((8000,10990))
       return self.attack

   def initReporting(self, results):
       results.setAttack(self.attack)
       results.setTraceManager(self.traceManager())
       self.results = results

   def doAnalysis(self):
       self.attack.doAttack()

Appendix D AES-256 IV Attack Script

NB: This script works for 0.10 release or later, see local copy in doc/html directory of chipwhisperer release if you need earlier versions

Full attack script, copy/paste into a file then add as active attack script:

#IV Attack Script
from chipwhisperer.common.autoscript import AutoScriptBase
#Imports from Preprocessing
import chipwhisperer.analyzer.preprocessing as preprocessing
#Imports from Capture
from chipwhisperer.analyzer.attacks.CPA import CPA
from chipwhisperer.analyzer.attacks.CPAProgressive import CPAProgressive
import chipwhisperer.analyzer.attacks.models.AES128_8bit
# Imports from utilList

# Imports for AES256 Attack
from chipwhisperer.analyzer.attacks.models.AES128_8bit import getHW

#Imports for IV Attack
from Crypto.Cipher import AES

class AESIVAttack(object):
   numSubKeys = 16

   @staticmethod
   def leakage(textin, textout, guess, bnum, setting, state):
       knownkey = [0x94, 0x28, 0x5D, 0x4D, 0x6D, 0xCF, 0xEC, 0x08, 0xD8, 0xAC, 0xDD, 0xF6, 0xBE, 0x25, 0xA4, 0x99,
                   0xC4, 0xD9, 0xD0, 0x1E, 0xC3, 0x40, 0x7E, 0xD7, 0xD5, 0x28, 0xD4, 0x09, 0xE9, 0xF0, 0x88, 0xA1]
       knownkey = str(bytearray(knownkey))
       ct = str(bytearray(textin))

       aes = AES.new(knownkey, AES.MODE_ECB)
       pt = aes.decrypt(ct)
       return getHW(bytearray(pt)[bnum] ^ guess)

class userScript(AutoScriptBase):
    preProcessingList = []
    def initProject(self):
        pass

    def initPreprocessing(self):
        self.preProcessingResyncSAD0 = preprocessing.ResyncSAD.ResyncSAD(self.parent)
        self.preProcessingResyncSAD0.setEnabled(True)
        self.preProcessingResyncSAD0.setReference(rtraceno=0, refpoints=(6300,6800), inputwindow=(6000,7200))
        self.preProcessingResyncSAD1 = preprocessing.ResyncSAD.ResyncSAD(self.parent)
        self.preProcessingResyncSAD1.setEnabled(True)
        self.preProcessingResyncSAD1.setReference(rtraceno=0, refpoints=(4800,5100), inputwindow=(4700,5200))
        self.preProcessingList = [self.preProcessingResyncSAD0,self.preProcessingResyncSAD1,]
        return self.preProcessingList

    def initAnalysis(self):
        self.attack = CPA(self.parent, console=self.console, showScriptParameter=self.showScriptParameter)
        self.attack.setAnalysisAlgorithm(CPAProgressive, AESIVAttack, None)
        self.attack.setTraceStart(0)
        self.attack.setTracesPerAttack(100)
        self.attack.setIterations(1)
        self.attack.setReportingInterval(25)
        self.attack.setTargetBytes([0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15])
        self.attack.setTraceManager(self.traceManager())
        self.attack.setProject(self.project())
        self.attack.setPointRange((4800,6500))
        return self.attack

    def initReporting(self, results):
        results.setAttack(self.attack)
        results.setTraceManager(self.traceManager())
        self.results = results

    def doAnalysis(self):
        self.attack.doAttack()