| As of August 2020 the site you are on (wiki.newae.com) is deprecated, and content is now at rtfm.newae.com. |
Difference between revisions of "CW308T-S6LX9"
From ChipWhisperer Wiki
| Line 10: | Line 10: | ||
[https://oshpark.com/shared_projects/ECbBlx58 OSH Park PCBs] | [https://oshpark.com/shared_projects/ECbBlx58 OSH Park PCBs] | ||
| − | |Supported Applications = | + | |Supported Applications = [[SimpleSerial | Simple Serial Enc]] |
|Programmer = Xilinx JTAG | |Programmer = Xilinx JTAG | ||
| − | |Status = | + | |Status = Released |
}} | }} | ||
[[File:spartan6_target.jpg|500px]] | [[File:spartan6_target.jpg|500px]] | ||
| + | |||
| + | == Example Project == | ||
| + | |||
| + | == Known Issues == | ||
| + | |||
| + | Note the -02 Revision of the PCB has swapped the markings of the CLKIN/CLKOUT. The correct pinout is: | ||
| + | |||
| + | * CLKIN connects to P84 | ||
| + | * CLKOUT connects to P85 | ||
| + | |||
| + | The CLKIN pin is a _N clock pin. If you need the _P clock pin, you can use a jumper on the CW308 board to route the clock input into the CLKOUT pin. | ||
== Programming == | == Programming == | ||
| Line 23: | Line 34: | ||
[[File:xilinx_jtag_small.jpg|400px]] | [[File:xilinx_jtag_small.jpg|400px]] | ||
| − | + | Options for programmers include: | |
| − | + | * Xilinx Platform Cable USB or USB-II (Digikey/Mouser). | |
| + | * Clone JTAG programmers off AliExpress/E-Bay for low cost (search 'Xilinx JTAG'). | ||
| + | * Digilent Inc HS1/HS2/HS3 Cables (NB: you may need separate jumper wires). | ||
| − | + | == Schematic == | |
See GIT Repo for PDF of schematic. | See GIT Repo for PDF of schematic. | ||
Revision as of 12:29, 10 September 2017
| CW308T-S6LX9 | |
|---|---|
 | |
| Target Device | Spartan 6 LX9 |
| Target Architecture | FPGA |
| Hardware Crypto | No |
| Design Files | OSH Park PCBs |
| Supported Apps | Simple Serial Enc |
| Programmer | Xilinx JTAG |
| Status | Released |
Example Project
Known Issues
Note the -02 Revision of the PCB has swapped the markings of the CLKIN/CLKOUT. The correct pinout is:
- CLKIN connects to P84
- CLKOUT connects to P85
The CLKIN pin is a _N clock pin. If you need the _P clock pin, you can use a jumper on the CW308 board to route the clock input into the CLKOUT pin.
Programming
The ChipWhisperer will eventually support programming this target. Until then, you will need an external programmer. This is connected via JTAG to the pin headers:
Options for programmers include:
- Xilinx Platform Cable USB or USB-II (Digikey/Mouser).
- Clone JTAG programmers off AliExpress/E-Bay for low cost (search 'Xilinx JTAG').
- Digilent Inc HS1/HS2/HS3 Cables (NB: you may need separate jumper wires).
Schematic
See GIT Repo for PDF of schematic.
Board Layout
See GIT Repo for gerber files.
